My Basket

0
You have no items in your shopping cart.

UKs No1 LED Bulbs and Drivers

  0113 3205011 | E: info@ledhive.co.uk

Mon - Fri : 9am - 6pm | Sat : 9am - 4.30pm

  • FREE Delivery On Orders over £75
  • 2 YEAR warranty
  • 30-DAY money back
  • 0% VAT
New! LH UT12W Driver
New! LH UT12W Driver New! LH UT12W Driver New! LH UT12W Driver

New! LH UT12W Driver

Availability: 348 In stock

£7.50

Quick Overview

  • Ultra Thin Driver from LED Hive - ZERO DELAY
  • Zero Interference with Dab radio and Wifi
  • Surge Protection - Hiccup mode - Recovers automatically after condition is removed
  • Thermal Short Circuit Protection
  • Safety Compliant:CE, RoHS & EMC - SELV Approved
OR

NEW Ultra Thin LED Drivers 


Easy to install simply remove old transformer and replace with these drivers.

If you feel that the LED bulbs you have just purchased are not bright as they should be, or are flickering, then you will require these drivers.

Your current transformers uses a lower frequency hertz and provides AC output which causes LED bulbs to flicker and a reduction in brightness. Running your bulbs with old transformers will surely reduce the life of the LED bulb. If you are going to spend money replacing your MR16 halogens with LED bulbs then please think about also replacing your transformers with these drivers. This will save you money in the long run. 

These LED drivers are suitable for all G4, MR11, MR16/GU5.3 LED bulbs and also most LED strip lights, just make sure the maximum wattage of the strip light does not exceed the output power of the LED driver

   

- Output Voltage (V) 12v DC

- Input Voltage (V) 240V AC

- 50/60Hz V

- Power output 0.5 - 12w

- Current 1000ma

-  Short circuit and overload protection

- Max Ambient Temp (deg. C) 45 deg. C

- Max Case Temp (deg. C) 75 deg C

- Size: L 128mm x W 50mm x H 11mm

 

Please Note: 

If you have a few LED lamps to dim, then the total wattage will not be enough to load the dimmer. For example, four 5w LED lamps in a small room will only total 20w whilst the minimum load on a 250w dimmer is 25w. This means that the dimmer will simply not work. In these circumstances a low load dimmer rated at 10w – 250w would be required. We recommend Hive Kengo LED Module or Varilight  

Under normal circumstances, so long as the minimum load is exceeded, dimming mains voltage LED lamps is not an issue so long as the minimum load is observed.

 

CE And RoHS Approved:

All Electrical work should be carried out by an qaulified Electrician

Average Life:

Average Life

Average LED lifespan in hours.

50,000
Also Called:

Also Called

This product may also be listed or called by one of these names.

Transformer | Drivers | Power Supply
Bulb Type:

Bulb Type

The type of chip used to produce light.

MR16 | Strip Light | GU5.3 | M11
Beam Angle:

Beam Angle

Light beam angle in degrees. Defines how wide the light is spread.

No
Base:

Base

Indicates the shape or form of the base usually using the width between pins or the diameter of the cap.

No
Cut Out:

Cut Out

This is the diameter of the opening required to fit the fitting.

No
Colour:

Colour

No
Certification:

Certification

Meets certification requirements.

CE - RoHs
Dimmable:

Dimmable

Can be used with an LED compatible dimmer switch.

No
Input Voltage:

Input Voltage

The power voltage supplied to the LED bulb usually 240v for mains or 12v with a transformer.

240v AC - 12v DC
Lumens:

Lumens

is the SI derived unit (symbol: lm ) of luminous flux, a measure of the total "amount" of visible light emitted by a source.

No
Manufacturer:

Manufacturer

No
Replacement for:

Replacement for

Light you would expect to obtain from the equivalent traditional bulb or lamp.

Transformer
Size (Dxl ):

Size (Dxl )

LED bulb measurements.

L 128mm x W 50mm x H 11mm
Wattage:

Wattage

The amount of power consumed (in Watts).

12W
MSRP:

MSRP

Recommended Retail Price. This is the retail price recommended by manufacturers for sale of their products.

18.50

NEW Ultra Thin LED Drivers 


Easy to install simply remove old transformer and replace with these drivers.

If you feel that the LED bulbs you have just purchased are not bright as they should be, or are flickering, then you will require these drivers.

Your current transformers uses a lower frequency hertz and provides AC output which causes LED bulbs to flicker and a reduction in brightness. Running your bulbs with old transformers will surely reduce the life of the LED bulb. If you are going to spend money replacing your MR16 halogens with LED bulbs then please think about also replacing your transformers with these drivers. This will save you money in the long run. 

These LED drivers are suitable for all G4, MR11, MR16/GU5.3 LED bulbs and also most LED strip lights, just make sure the maximum wattage of the strip light does not exceed the output power of the LED driver

   

- Output Voltage (V) 12v DC

- Input Voltage (V) 240V AC

- 50/60Hz V

- Power output 0.5 - 12w

- Current 1000ma

-  Short circuit and overload protection

- Max Ambient Temp (deg. C) 45 deg. C

- Max Case Temp (deg. C) 75 deg C

- Size: L 128mm x W 50mm x H 11mm

 

Please Note: 

If you have a few LED lamps to dim, then the total wattage will not be enough to load the dimmer. For example, four 5w LED lamps in a small room will only total 20w whilst the minimum load on a 250w dimmer is 25w. This means that the dimmer will simply not work. In these circumstances a low load dimmer rated at 10w – 250w would be required. We recommend Hive Kengo LED Module or Varilight  

Under normal circumstances, so long as the minimum load is exceeded, dimming mains voltage LED lamps is not an issue so long as the minimum load is observed.

 

CE And RoHS Approved:

All Electrical work should be carried out by an qaulified Electrician

Use spaces to separate tags. Use single quotes (') for phrases.

  1. Perfect Review by Kevin H
    Price
    Quality
    Value

    I was looking for a low ampere transformer to power my Plinth lighting in my new kitchen and this was a prefect fit. It was easy to connect and appears to be of high quality. Next day delivery was important. (Posted on 06/10/2018)

  2. Excellant Review by Paul F
    Price
    Quality
    Value

    This is the second time I have used this product to replace the transformer for halogen light fittings to convert them to LED. Product quality appears good, with terminals that clamp strongly. (Posted on 06/10/2018)

  3. Very good. Reduced bathroom light power consumption from 250 watts ... Review by Mr J
    Price
    Quality
    Value

    This LED driver has been in use for a month now. It works fine for low power LED lighting, arrived promptly and was exactly as described in the information. Fitting was simple and there have been no problems at all. (Posted on 06/10/2018)


Write Your Own Review

Only registered users can write reviews. Please, log in or register

Certification